1. Home
  2. Fit comments service

Fit comments

Your fit sample is back. We write the corrections.

Send photos of the sample on a body or a form and the measurements you took. We compare them with the spec and write a fit comment sheet the factory can act on, with revised points of measure for the next sample.

Get a quote for fit comments See a fit comment sheet

Free quote · Reply within 24h · No physical sample needed · No cut of your production

Fit comments price$89 per style Per fit round. Scope confirmed by email before any work starts.
Hands holding a woven shirt placket finished with a contrast blue blanket stitch
Hand finishing: blanket stitch on a placket

Fit comments · sample 1Style: crewneck tee

Fit comment sheet: spec, sample 1 as measured, difference and revised spec. Example values in centimeters
POMSpecSampleDiffNext
A53.055.0+2.053.0
B72.071.0−1.072.0
C21.023.0+2.020.0
D18.018.00.018.0

A Take in 1.0 at each side seam, blend to the armhole.

Example valuesRevised POMs for sample 2

How fit comments are written

Measured on the sample, written for the factory.

We measure the fit sample against the spec, note what changes and why, and send revised points of measure.

  • Several hands pinning and marking a cream shirt on a dress form, with red tape lines and a tape measure
    On the formMarking a fit on the dress form
  • Hands measuring across the shoulder of a fitted top with a tape measure
    ShoulderMeasuring across the shoulder
  • Measuring the sleeve of a black jacket with a tape measure
    SleeveMeasuring the sleeve
  • Measuring a black bodysuit at the waist with a tape measure
    WaistMeasuring the waist

Fit comment sheet

What was wrong, what changes next.

Drag the handle. On the left, sample 1 as measured against the spec; on the right, the revised spec the factory works from for sample 2. The sheet below says the same in words the sample room can act on.

Sample 1, as measured Revised spec

Illustration, example values in cm

Fit comments: crewneck tee, sample 1Base size M · cm

Fit comment sheet with spec, sample 1 measurement, difference, tolerance, comment and revised spec. Example values in centimeters
POMDescriptionSpecSample 1DiffTol ±CommentSample 2
A1/2 chest, 2.5 cm below armhole53.055.0+2.01.0Out of tolerance. Take in 1.0 at each side seam, blend to the armhole.53.0
BBody length from HPS72.071.0−1.01.0Within tolerance. No change.72.0
CSleeve length from shoulder point21.023.0+2.00.5Out of tolerance. Fit decision: also shorten the spec by 1.0.20.0
DNeck width, seam to seam18.018.00.00.5OK.18.0
ENeck rib height2.02.5+0.50.3Rib too high, puckers at center front. Back to 2.0.2.0

Example values, not a client order

What you get

Four parts, one next sample.

A fit comment sheet the factory can work through without a call: numbers, pictures, the new spec and a short list of changes.

  • POMSpecS1Diff
    A53.055.0+2.0
    C21.023.0+2.0
    D18.018.00.0

    Part 01Example values

    Measured vs spec

    Every point of measure: spec, what the sample measured, the difference and the tolerance, with out-of-tolerance lines marked.

  • 123

    Part 02Example values

    Comments on your photos

    Numbered comments pinned to your fit photos: drag lines, twisting, puckering, where the fabric pulls.

  • POMWasNow
    C21.020.0
    E2.02.0
    A53.053.0

    Part 03Example values

    Revised points of measure

    The updated spec for the next sample, old value and new value side by side, so nothing changes by accident.

    1. Take in side seams 1.0
    2. Shorten sleeve 3.0 at hem
    3. Neck rib back to 2.0
    4. Keep body length

    Part 04Example values

    Next-sample list

    What the factory must change, in the order a sample room works, and what stays exactly as it is.

The team behind every pack

Real people draw every tech pack.

Our studio team in the USA drafts every flat, measurement and note, and answers your revision rounds by email. No template generator, no guesswork.

  1. Team at a table reviewing printed sportswear flats and color swatches, with the designs on a screen behind Reading a brief with flats and swatches
    01

    We read your brief

    Sketch, reference photo or sample: someone on our team reads it and replies within 24 hours with the tier, the price and the timeline.

  2. Tech pack page with front, side and back technical flats of a raglan active t-shirt Example page
    02

    We draw the flats

    A technical designer draws every view to proportion, with numbered callouts for each seam, stitch and trim.

  3. Vest tech pack page with front and back flats, a graded measurement table and a bill of materials Example page
    03

    We grade and spec

    Measurements graded across your sizes with a tolerance on every line, plus the bill of materials and construction notes.

  4. Technical designer kneeling to measure the inseam of a fit model with a tape measure Measuring the inseam on a fit model
    04

    A second person checks every measurement

    Before delivery, someone who did not draw the pack checks every point of measure against the flats. Then 2–3 revision rounds by email.

Get a quote for your tech pack How we work

Example pages are shown with the brand removed. Photos show the kind of studio work behind each step.

What to send

Photos and numbers, no parcel needed.

We work from your photos and measurements, so the sample stays with you. If a photo does not show what we need, we ask for another angle before writing a comment.

Send us

  • Fit photosFront, side and back on a body or a form, in the base size, plus close-ups of problem areas.
  • Your measurementsTaken flat on the sample. No how-to-measure sheet? We send one first.
  • The specYour tech pack or measurement spec, whoever made it.
  • Fit notesWhat the person who tried it on felt: tight, long, pulling, twisting.

Right service?

  • Yes, if a sample came back and you are not sure what to tell the factory.
  • Yes, if the factory asked for “fit comments” and you have none.
  • No, if you need the pattern itself corrected: your factory or pattern maker makes that change from our comments.
  • No spec yet? Start with a tech pack review or the full tech pack.

What it costs

$89 per style

Per fit round. Scope and timeline confirmed by email before any work starts.

Get a quote for fit comments

Inside the studio

Where the work actually happens.

Pattern tables, dress forms, sample rails and swatches: the places your file will be read. Our studio team in the USA writes every note for them.

  • Overhead view of a team measuring and adjusting a garment on a cutting table
    Measuring on the table
  • Sewing corner with machines on a white desk and thread spools on a pegboard
    Sampling corner
  • Pattern studio with a dress form, pattern pieces on the wall and a cutting table
    Pattern corner
  • Team at a table reviewing black garment samples beside large windows
    Sample review
  • Bright studio with a long work table and rails of clothing along the walls
    Sample rails and work table
Get a quote for your tech pack

Free quote · Reply within 24 hours · Flat fee per style · Studio team in the USA

Before you send it

Straight answers on fit comments.

What a fit sample is, what the sheet holds, and what we do not change.

Not on the list?

Ask us with your brief.

We reply within 24 hours. Or email garmentspec@gmail.com.

Get a quote

The first garment a factory sews from your spec, made so you can check the fit before anything else is approved. It is tried on a body or a form, measured and compared with the spec.

The document you send back after a fit sample: each point of measure with the spec, what the sample measured and the difference, plus written comments and the revised measurements for the next sample.

No. Photos on a body or a form and your measurements are enough to write the comments. If a photo does not show what we need, we ask for another angle first.

No. We write the corrections and the revised measurements. The pattern change itself is made by your factory or your pattern maker.

Yes. We work from whatever spec the factory used. If the spec is missing points we need, we say so and suggest a tech pack review.

$89 per style for each fit round. We confirm the scope and timeline by email before any work starts.

Your fit sample

Send the photos. We write the comments.

Tell us the style and the fit round. Fit comments are $89 per style per fit round; we reply within 24 hours and confirm the scope by email before any work starts.

  • Fit photosFront, side, back and close-ups.
  • Your measurementsTaken flat on the sample.
  • The specThe tech pack the factory used.
  • Fit notes If anyWhat felt wrong when it was worn.
Get a quote for fit comments Tech pack review

Free quote · Reply within 24h · Price confirmed by email before any work starts · garmentspec@gmail.com

Submission Successful

The form has been successfully submitted.